View TQM613017_7896105.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 1 functional block diagram product description triquint?s TQM613017 is a fully matched pa/duplexer, front end module (fem) for cdma/amps use in mobile phones. the 8 x 5 x 1.52 mm, 22-pin module includes an integrated saw duplexer, power amplifier, transmit filter, rf power detector and logic controller. with an rf power output up to 25.5dbm the TQM613017 fem meets the strict acpr and altr requirements for products designed to the is-95/98 standards. the quie scent current of the pa/duplexer is set by the base-band processor using a 1-bit bias control (vmode) to minimize battery consumption and maximize talk time. triquint?s multilayer laminate technology provides low loss interconnect and optimized match between the duplexer, pa and filter enabling the TQM613017 to achieve typically 430 ma current consumption at maximum output power (+25.5dbm). the small 8.0 5.0 mm module replaces four separate components requiring less board space. tqm613107 provides handset designers with a simple to use surface mount module requiring minimal external circuitry in the new generation of small and light phones. electrical specifications parameter min typ max units frequency 824 836.5 849 mhz cdma mode pout 1 +25.5 dbm cdma mode acpr (+/- 885khz offset) 1 -51 dbc cdma mode altr (+/- 1.98 mhz offset) 1 -59 dbc cdma mode current consumption 1 460 ma cdma mode leakage 1 -30 dbm ant-to-rx insertion loss 2.8 db rx noise -181 dbm/hz features ? ingap gaas hbt pa ? low current consumption typical: 460ma @ +25.5dbm ? low quiescent current typical: 40ma ? 1-bit bias control for extended talk time ? integrated power detector ? integrated duplexer and interstage filter ? excellent acpr typical: -51 dbc @ +/- 885khz offset ? excellent altr typical: -60 dbc @ +/- 1.98 mhz offset ? low voltage operation 1.3 v to 4.4 v ? small profile 22 pins, 8.0 x 5.0 x 1.52 mm ? reduced phone board space replaces 4 separate components ? easy to use with few external components internally matched inputs and outputs applications ? is-95/cdma2000 ? single-mode, dual mode, and tri mode cdma/amps phones package style TQM613017 top view through package vref TQM613017 top view through package TQM613017 top view through package vref note 1: test conditions v cc =3.4 v, v ref =2.85 v, t=+25c absolute maximum ratings 1
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 2 parameter symbol min. max. units rf input power p in - 10.0 dbm supply voltage v cc - 6.0 volts reference voltage v ref -0.5 3.5 volts vmode (1 bit bias control) v mode -0.5 3.5 volts venable v en -0.5 3.5 volts case operating temperature t case -30 +85 c storage temperature t store -55 +125 c msl msl-3, +260c note 1: the part may not survive all maximums applied simultaneously. dc electrical characteristics parameter symbol min. typ/nom max. units supply voltage p out =13.5dbm to 25.5dbm p out < 13.5dbm v cc 3.2 1.3 3.4 3.4 4.4 4.4 volts volts reference voltage v ref i ref_h (v en=h ) i ref_l (v en=l ) 2.75 2.85 2.95 15 1 volts ma ma vmode (1 bit bias control) high bias mode (high power state) low bias mode (low power state) v mode_h v mode_l i mode 0 2.35 - 2.6 0.5 2.85 1 volts volts ma venable v en_h v en_l i en 2.35 0 2.6 2.85 0.5 1 volts volts ma case operating temperature t case -30 25 +85 c power range truth table power state vref vmode ven range high power 2.85 v low high +13.5 dbm to +25.5 dbm low power 2.85 v high high < +13.5 dbm shut down 0 v high or low low - note 1: logic low is 0 v to +0.5v, logic high is +2.35 v to +2.85v
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 3 cdma (is-98c) electri cal characteristics 1 parameter conditions min. typ/nom max. units rf frequency 824 849 mhz power output po_h po_hvt po_m po_l vcc=3.4, 25ct>85c, vmode = low vcc=1.3 to 4.4v, -30c>t>85c, vmode = high vcc=1.3 to 4.4v, -30c>t>85c, vmode = high 25.5 24.5 13.5 -52.5 dbm dbm dbm dbm large signal gain g_h g_hvt g_m g_mvt vcc=3.4v, 25c, vmode = low, po_h vcc=3.2 to 4.4v, -30c>t>85c, vmode = low, po_h vcc=1.3 to 3.4, 25c, vmode = high, po_m vcc=1.3 to 4.4v, -30c>t>85c, vmode = high, po_m 20 18 11 9 28 30 28 28 db db db db i average vcc=3.4v; vref=2.85v; temp=25c, vmode=2.85v pout = suburban profile 75 90 ma gain flatness gflat_h gflat_l vcc=3.4v, t=25c, po_m to po_h vcc=3.4v, t=25c, po_l to po_m -3 -3 3 3 db db gain sensitivity gsen_v gsen_t vcc=3.2 to 4.4v, 25c vcc=3.4v, -30c>t>85c -1.25 -3.0 1.25 3.0 db db quiescent current (i ccq ) no rf power 30 55 ma standby current (i stby ) -30c TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 4 parameter conditions min. typ/nom max. units ruggedness pout = +25.5dbm, 10:1 vswr all phases; rx port 5:1 vswr all phases. no damage/degradation pout=+25.5dbm, 0ct>85c 20 18 28 30 db db pae pout = 28dbm, vcc=3.4v, 25c 31 % note 1: test conditions: v cc =3.4v, v ref =2.85v, t c = +25 c, unless otherwise specified. rx characteristics parameter conditions min. typ/nom max. units center frequency -30c TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 5 power detector characteristics parameter conditions min. typ/nom max. units range vcc=3.2 to 4.4v, -30ct>85c pout=15dbm to 29dbm, vswr=1.5:1, all phases, vcc=3.2 to 4.4v, -30c>t>85c -1.7 -0.4 1.7 0.4 db db detector error (low power) dem_l1 dem_l2 pout=5dbm to 15dbm, vswr=4.5:1, all phases, vcc=3.2 to 4.4v, -30c>t>85c pout=5dbm to 15dbm, vswr=4.5:1, all phases, vcc=3.2 to 4.4v, -30c>t>85c -2.5 -1.5 2.5 1.5 db db variation in delivered power (d_pv) pout=22dbm to 29dbm, vswr=3.5:1, all phases, vcc=3.2-4.4v, -30c>t>85c -3.5 1.0 db detector output range (v_dr) pout=5dbm to 29dbm, vcc=3.2 to 4.4v, -30c>t>85c 0.1 2.5 v detector voltage range @ 5dbm (v_dl) vcc=3.2 to 4.4v, -30c>t>85c 0.1 v detector voltage range @ 29dbm (v_dh) vcc=3.2 to 4.4v, -30c>t>85c 1.75 2.5 v detector output impedance (off) vcc=3.2 to 4.4v, -30c>t>85c, ven=low 100 k-ohm detector slope sv_l sv_h pout=5dbm to 15dbm, vswr=1.5:1, all phases, vcc=3.2-4.4v, -30c>t>85c pout=15dbm to 29dbm, vswr=1.5:1, all phases, vcc=3.2-4.4v, -30c>t>85c 8 140 mv/db mv/db detector time response tdon tdoff vcc=3.2 to 4.4v, -30c>t>85c vcc=3.2 to 4.4v, -30c>t>85c 30 30 us output ripple (prpl) vcc=3.2 to 4.4v, -30c>t>85c -0.3 0.3 db
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module pin out and assignments vref pa tx filter detector coupler duplexer control vref pa tx filter detector coupler duplexer control pin symbol description 1 n/c no connection 2 v en enabe/disable 3 v ref reference dc supply (regulated) 4 v mode digital bias mode control input 5 v det detector voltage output 6 gnd ground 7 gnd ground 8 n/c no connection 9 gnd ground 10 ant antenna port 1 11 gnd ground 12 n/c no connection 13 gnd ground 14 rx receiver output port 1 15 gnd ground 16 v cc2 dc supply (battery) 17 v cc1 dc supply (battery) 18 gnd ground 19 n/c no connection 20 rf in transmit input port 1 21 gnd ground 22 gnd ground note 1: dc block included inside the module. data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 6
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module typical test circuit triquint offers our customers the below evaluation board as a m eans for testing and analysis of 8 x 5mm pa/duplexer. the evalu ation board schematic and picture are provided for preliminary analysis and design. the resistors r1/r2 can be optimized to tradeoff the acpr/icc performance at medium/low power range. evaluation board dut c2 c3 c1 c4 c5 c6 c7 r2 r1 dut component layout c2 c3 c1 c4 c5 c6 c7 r2 r1 dut component layout vdet vmode vreg ven vcc vcc gnd gnd signal description gnd common ground gnd common ground vcc dc supply (battery) vcc dc supply (battery) ven module enable/disable (digital) vreg dc supply (regulated) vmode bias mode control (digital) vdet detector voltage note: both gnd terminals and vcc terminals are tied together on the apps pcb. single row 8-position 0.1? header pins vdet vmode vreg ven vcc vcc gnd gnd signal description gnd common ground gnd common ground vcc dc supply (battery) vcc dc supply (battery) ven module enable/disable (digital) vreg dc supply (regulated) vmode bias mode control (digital) vdet detector voltage note: both gnd terminals and vcc terminals are tied together on the apps pcb. single row 8-position 0.1? header pins data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 7
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module evaluation board and typical phoneboard schematic data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 8
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module applications information: power up/down sequences power-up sequence data sheet: for additional information and latest specifications, see our website: www.triquint.com revision d, april 30, 2007 9 power-down sequence sequence pin description 1 v cc apply battery voltage 2 v ref apply reference voltage 3 v mode set bias mode 4 v en enable pa 5 rf apply rf sequence pin description 1 rf remove rf 2 v en disable pa 3 v mode set bias mode to 0v 4 v ref remove reference voltage 5 v cc remove battery voltage
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module pc board layout recommendations 10
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module recommended reflow profile the TQM613017 is rated for 260oc reflow profile. below is a ge neral recommendation for 260oc reflow. the specific profiled used will need to take into account the requirements of the board used, other co mponents used, and the specific layout of the components. the fol lowing recommendation should be used as a guideline only. 11
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module packaging and ordering information package dimensions: 12
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module package dimensions: package marking: pin 1 TQM613017 cccc aaxxxx-z yyww top mark pin 1 TQM613017 cccc aaxxxx-z yyww top mark 1) line 1 : product code = TQM613017 2) line 2: country code = cccc (usa = united states, phil = philippines) 3) line 3: aaxxxx-z = aa = vendor code + xxxx = triq uint lot number + z = sub lot # (1, 2, 3, ?) 4) line 4: yyww = year and work week 13
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module tape and reel specification: 613017 14
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module tape and reel specification: xxxx 15
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module shipment box & label description: 16 tape & reels will be packaged in a drypack bag and then in na shipment box. the box dimensions will depend on the number of reels shipped in each box and are noted in the t able below. the box label and a description of each item on the label is also shown below. xxxx 13 inch x16mm--drypack box size reel qty/box empty box wt w/ packing 15x15x7 3 2 18x15x11 5 2.36 17x16x17 9 2.76 ship from: triquint semiconductor, inc 2300 ne brookwood parkway hillsboro, or 97124 ship to: recipient address information here (3s) pkg id: 581+23047123 (k) trans id: 812934657 (p) cpn: 5871-2489 (q) qty: 20000 (1p) spn: tqd777001 (13q) pkg count: 1/1 package weight 3.0 lb / 1.36 kg mpn: 1005859 supplier code: 10 character max. + tqs shipper number. (pkg. id/serial number) customer purchase order. 20 character max. customer part number. 22 character max. supplier product number. 21 character max. quantity. box count (1/3, 2/3, etc.) manufacturer's part number format: 4 * 6.5 in 102 * 166 mm code 39 1:2 all barcodes contain data identifier followed by data, e.g. k812934657
TQM613017 data sheet powerpad tm cdma/amps cellular ba nd pa/duplexer module lead-free statement: all new triquint products/packages in troduced since june, 2003 ar e qualified using rohs comp liant pb-free plating. labels on the tape reel and the shipping carton will include the lead free logo. TQM613017 5 x 8 mm package has gold (au) plated contacts. pb b additional information 1 this product is compliant with rohs material restrictions and is rated msl level 3 per jedec standard ipc/jedec j- std-020. 1 for latest specifications, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: (503) 615-9000 email: info_wireless@tqs.com fax: (503) 615-8902 for technical questions and additional information on specific applications: email: info_wireless@tqs.com the information provided herein is believed to be reliable; triquint assumes no liability for inaccuracies or omissions. triqui nt assumes no responsibility for the use of this information, and all such information shall be entirely at the us er's own risk. prices and specifications are subject to change without notice. no patent rights or licenses to any of the circuits described herein are implied or granted to any third party. triquint does not authorize or warrant any triquint product for use in life-support devices and/or systems. copyright ? 2004-5 triquint semiconduc tor, inc. all rights reserved . 17

▲Up To Search▲

Price & Availability of TQM613017

	To Download TQM613017 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .